- I owned an SR400 and the carb fit so tightly inside the frame so I cannot adjust the idle screw. Thankfully I've found this product for my carb and even my bike.Read More
- Idling AdjusterIt's easy.Read More
- Bought this for an extension as the adjustment Knob fitted as standard is too short.Good to be able to adjust Idol easily!Read More
- Fits:
- KAWASAKI
I bought it along with the FCR Carburetor Bodycarburetor when I was riding my 250sb.It is easy to install the carburetor if you have a short Hexagonal Wrench.Read More - Fits:
- YAMAHA SR500 78-87
- YAMAHA SR400 78-87
When I installed the FCR Carburetor Body on my 87 sr500, the motorcycle shop mistakenly ordered an adapter for CV Carburetor models after 1988, so I had to modify the air cleaner joint every time I in...Read More - I bought it to adjust the idol of the KEIHINCRSPECIAL KnifeIt's not an Option or anything like that, but it's so much more than just a carburetorBody that I want it to be included in the carburetorBod...Read More
- You should be able to get the negative pressure out of the Spigot and Indicator so that Merit can be used to get the negative pressure out of the I bought it because of its large sizeIf you forget to ...Read More
- I think it's a must-have item, so I wish it was included in the body from the beginning But I don't think that Carburetor which I bought second-hand often comes with these itemsI've always used Tie Wr...Read More
- Fits:
- DUCATI
The hole machining for Main Air and Pilot is messyIt has little impact, but it's also slightly out of position and the BALI taking is messyI don't want you to be invisible but I don't want you to cut ...Read More - Screw department was M5 and Pitch was searching for ordinary Adjuster.I bought it by understanding that this is so in other people 's impressions.There is no item with explanation of the Screw dep...Read More
- It was better if you know the Large Kimono and Pitch of Screw club.Since I looked it up from Review, I also posted it.It probably will not work as we have not written any other Manufacturer.Read More
- Attention is necessary when diverting this Parts. Screw part at the tip is M5 and Pitch is 0. It is 8.. My Motorcycle is 0. It was 5 so it could not be diverted. Those who are thinking about diverting...Read More
- Idling adjustment of KEIHINCR carburetor, ESTRELLA Frame interferes and can not be rotated by Slotted screwdriver - - It is very difficult to turn fingers, but it is very difficult to turn around with...Read More
- There are other Adjuster for carburetor of KEIHIN, but it is aiming for this product if it is used for a long time. For the other carburetor Body, the item of Fixed Type is not good feeling of Idling ...Read More
- CRcarburetor 's Idle Screw is in a painful place and it is unthinkable to continue to use it without this Adjuster! Although there are other Adjusters of other Manufacturers too, it is a Type fixe...Read More
- Since it was used as a negative pressure outlet for the Carburetor, I needed to use the KITACONBR Rubber cap to cover it up. [Inner diameter of 3.8mm] separately.Exclusive Washer again. [Gasket] Also ...Read More
- ESTRELLA is very narrow between Frame and CRcarburetor Idling Adjustment Screw and can not be adjusted with your fingers,Because it was expensive, I refrained from purchasing, but I bought it because ...Read More
- CRcarburetor, since IdolRingScrew is in the middle of Body, degree of adjustment,Since hands hit Fuel Tank and it was troublesome, expectation for ease of adjustmentPurchase.When this part is installe...Read More
- Aprilia / RS125 Carburetor, OEM's Dell'Orto / From PHBH 28, KEIHIN / I am exchanging with PWK33.However, because Idol adjustment can not be easily done, I was looking for Idle Screw, but there...Read More
- Adding CRcarburetor to SRX and Idling Adjustment Screw is hidden in Tank and adjustment is impossible because it is impossible. It is more likely to have a Bracket that can fix Knob to carburetor Body...Read More
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING