K-FACTORY Exhaust Gasket E
When I replaced the Exhaust System, I also replaced the Gasket. I chose this product because it was a little cheaper than other companies' products. There is no problem at all. I think that it is easy...
 |  |  |
| | | |
 |  |  |
| | | |
 |  |  |
| | | |
K-FACTORY Radiator Core Guard Honeycomb Mesh Core ...
Material is thin and strength is a little uncertainMaterial:I like that it's Stainless Steel.
K-FACTORY Footpeg TYPE 2
I tried to put it on my vSTROM650, but it's not engraved, and if I put Damper's on it, the hole would be blocked.
K-FACTORY Footpeg Bracket
Back & Up just a little bit. You can install it between footpeg and Frame. It's not difficult to install.However, since the Brake Side is co-clamped with the Master Cylinder, it seems to need a little...
K-FACTORY STD Position Corresponding Aluminum Exha...
I went with the frosted Black to match the Frame as shown in the photo, but the actual product is a careful Material:Polishing.It is for removing Tandem Footpeg, but Aluminum Collar is included so tha...
K-FACTORY CLR + Full Exhaust System
Compared with NORMAL, the car body has become very light. The sound is still Japanese Vehicle Inspection Correspondence, so it is a bit suppressed. But I think the sound quality is good.The insert is ...
K-FACTORY STD Position Corresponding Aluminum Exha...
I bought it because I removed the Tandem Footpeg.The installation was done by Yoshimura, but even the OEM unit comes with no problem.
![K-FACTORY CSR + Full Exhaust System Standard Type [JMCA Certification]](http://img-webike-370429.c.cdn77.org/catalogue/images/80467/179KRFDAZE0000_1_TS.jpg)
K-FACTORY CSR + Full Exhaust System Standard Type ...
I used to have a yoshimura t-spec, but I replaced it for commuting use. Installation was easy.The Silencer has quite a bit of silencing material in it.When I contacted Manufacturer they said the volum...
K-FACTORY Stand Hook M8
I have no complaints whatsoever about normal use!The dress-up effect is perfect!However, when it is used together with the exhaust system of LOWMount type of YOSHIMURA, it hits and shaves.The suspensi...
 |  |  |
| | | |
 | ||
| |
K-FACTORY Handlebar Up Kit
[How is it used?I wanted to adjust the Handlebar.Was the one you received as per Image?＊Image StreetWas the installation difficult?Maybe it depends on how the screw lock works?How was your experience ...
K-FACTORY Silencer Emblem
I really like the K-FACTORY Emblem with its good design. There is a thin layer of Vinyl on the emblem from the beginning to prevent scratches and other problems. If you try to remove it later, it won'...
K-FACTORY Meter LED Set
It is A14, but I was not able to install T5 bulbs. Compared with the original bulb, the mating part is a little large and could not be installed. It is in use only. It was past the return deadline and...
K-FACTORY Change Shaft Holder
To tell the truth, I myself have never experienced GEAR exits with this vehicleWhether this is an individual difference or a difference in Shift change habits is unclearAs far as the Net video is conc...
K-FACTORY Clutch Release B Type
Beautiful and functional! I purchased this mostly for looks, but it indeed decreases lever pull. Installation is easy and it comes with fasteners and a bleeder.
K-FACTORY Change Shaft Holder
I've been dissatisfied with the accuracy of KFACTORY's products, even with other productsIt's a shame, because the point of view is good This product is also 1Race and Bearing is outI contacted the Ma...
K-FACTORY Cylinder Inlet Single Item
NORMAL is painted on Iron Pipe, but the front wheels are painted with sand and small stones that are rolled up was peeling and rustingIf the rust continues to develop, it will cause water leakage:I re...
K-FACTORY Clutch Release K Type
It is a rather expensive part, the shape of the part is not so different from NORMAL, and the Clutch I wasn't sure how much lighter it would be, so I was nervous until I actually used itI read somewhe...
K-FACTORY Shaft Holder
Craftsmanship is excellent. Aluminum milling is precise, and anodizing is well done. The spacers are also aluminum (anodized black).
Installation was easy on a 2014 Grom, but I did have one minor p...
 |  |  |
| | | |
 |  | |
| | | |
K-FACTORY Top Cap Wrench
I bought it for Oil exchange.Just by applying to Top cap you can see the goodness of precision.I actually tried opening the top cap, but I think that it is a good item that does not contain any scratc...
 | ||
| |
K-FACTORY Design Cap
The perfection of Cap itself is high, texture is also good.Embroidery of KMark, embroidery of SIDE department is also very polite finish.Although the price is not cheap, it is convincing because thing...
?
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING