[Specification] ・Rated voltage: DC12V ・Outer diameter dimension: W25.5mm x H30.5mm x D15.5mm (*excluding protruding parts)
[Components] ・SPI-110 C1 main unit x 1 ・Model Specific Harness x 1 ・Various double-sided tapes ・Instruction manual *Components vary by kit.
*When the clutch is depressed while driving, the display shows a gear other than the one in which the clutch is engaged, but this is not a malfunction. *Prioritize safety while driving and do not be careless in front.
*Please do not use non-resistive spark plugs.If you use a plug without resistance, noise may be generated and the rotation signal may not be input correctly, so please use a spark plug with resistance. *Please put the attached double-sided tape on the back side of this product to prevent water from entering because there is a switch. *Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage. *After installing this product, periodically inspect it to see if any parts have fallen off. *PROTEC is not responsible for any damage or accident caused by the use of this product. *Protec is not responsible for any labor charges for removal or other expenses incurred during repair. *All vehicles that have been tested by Protec are stock.There is a possibility that a problem may occur if the vehicle is equipped with aftermarket parts other than stock parts. *Please refer to the service manual of your motorcycle to confirm the respective wiring before installation.
●All the necessary parts are included in this kit!Easy installation with special harness! It can be installed easily without soldering because it uses a special harness for each model. *The vehicle-specific harness has a 12V (+) service terminal for easy installation of the CS-550 burglar alarm.
●Compact design! The main unit dimensions are W25.5mm X H30.5mm X D15.5mm (excluding protruding parts), a compact design that does not interfere with installation around the meter.
●LED display for high visibility! Equipped with a dimmer sensor [automatic dimming function].The brightness of the LED is automatically adjusted to be brighter in the daytime and darker at night to improve the visibility of the digital numerals.
●Equipped with a shift up indicator! Since the rpm can be set arbitrarily, it can be used for everything from narrowing to preventing over-revving.The blue LED will light up when the rotation is higher than the set value. *You can re-register as many times as you like.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
What made you decide to buy? Takekawa:Change to a TAF 5-speed Close Ratio Transmission Kit, and visually I bought it because I wanted to check the shift position and the GROM It would have been nice to be able to check the Shift position in the OEMMeter, but.. I guess they didn't adopt it because of the Cost (tears) In the case of OEMGEAR and TAF 5-speed Close Ratio Transmission Kit Likewise, I'm going to do a phantom TopGear changing (sweat) Protec:SPI- After installing the M10 Shift position Indicator, the phantom Top gear is gone
How was your experience with it? When GEARUp/Down, it is not displayed immediately It is displayed after a little delay The place where Neutral is displayed as 0 is a regrettable place I don't want to worry about it because I only use it........ If it's not OEMSprocket, initial learning is required, except for OEMGEAR and No initial training is required for the OEMSprocketSpec By the way, if you need a Shift Up Indicator, you can use OEMGEAR and OEMSprocket MyGROM can be used as it is if it is not necessary though it is necessary to set also Both Sprocket and GEAR have been replaced, so an initial learning curve was necessary Initial learning can be done on a real run or on Maintenance Stand I used the maintenance stand to do the initial learning I used the maintenance stand to do the initial learning while watching the meter If you have a Course, you can do the actual run
Was the installation difficult? To install it, remove the OEM meter and connect it to the OEMConnector You only need to insert the Harness Because the power supply and the Earth connection are not necessary, it is a pompous installation However, because it has to do waterproof processing, that is a Large strange place, but The Instruction Manual for Handling describes it in detail, so take your time I think you can't go wrong if you hang it up and work with it Also, the Harness for car models has a 12V service terminal I connected the power line of KOSO Mini3Digital A/F ratio meter to this terminal
【Please tell me the installation point and hang】 Since the OEMConnector is interrupted by the vehicle-specific Harness, the Light It's a matter of putting the Wiring together well Also, Waterproof treatment is a spec. to put the attached Seat As I mentioned before, you should work slowly and without haste However, the Construction Manual provides details, so please take the time to review it Please
[Was the Instruction Manual easy to understand? The initial learning content is described in this manual, which is difficult to understand after just one look at it You can learn the initial study over and over again, even if you get it wrong, so when you do, the Instruction Manual to review and relearn Once you've successfully completed your learning, the Instruction Manual is easy to understand! That's what I mean
[Included Parts:were they on? Comes with Bar Handlebar Bracket and Double-sided Tape Compatible Handlebar Diameter of the Bar Handlebar Bracket:22.2mm/1 Inch (up to Large35mm) Double-sided tape can be used after the initial learning is completed if the initial learning is required On the back of the Indicator there is a Switch that is required for initial training If the initial training fails, you will have to remove the double-sided tape in order to re-learn it Note that it is notView Detail
Because the Cable set is complete with the product exclusively for vehicles, tools for Line etc etc. I do not need anything. The picture of Instruction Manual is former Grom, but WiringCableetc. There is no problem as it is the same for new Gromm. Cable becomes an interruption shape and Rubber cover for OEM waterproof can not be used ...... WaterproofTape is also Quantity : 1 Set of 2pc. It is safe because it is done.. It is already adjusted by OEM's GEAR ratio in the state of shipment of goods (If you are replacing 5-Gear or not fighting Engine Displacement Volume with Large) You can use as it is.
* I'm raising a Sprocket on the Drive side, but I can still use it without problems.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!