Brake Pad RX3 [Standard Type/Street, Race]

I used it for MOTO GUZZI.

Fits:MOTOGUZZI 1200 Stelvio 08 Location:Rear:1, VERTEMATI C 500 02- Application Area:Front Number Required:1, VERTEMATI E 501 02- Application Area:Front Number Required:1, VOR MX 350 02- Application Area:Front Number Required:1, VOR EN530 00- Place of use:Front Necessary quantity:1

Japanese Webike user

Excellent

Feb 16, 2021

2020 by Corona
I bought it because the Shop told me that the part would not come in and I would have to replace it myself.
As for the Exchange Kill.
It was easy, but it's an important safety part and you are responsible for it.
If you're not sure, Shop is a good place to start.

Now, the impression that I used this Pad.
(This is assuming that you are only using the bike for touring.

It stops securely with no problems.
Touchetc. is not a problem either.
I don't know about durability yet.
Therefore, it is unrated.

It's not bad.

Helpful?

Very Good

Jun 25, 2015

Recommended

I usually do not use Rear brake much, but since BMW's Integra Le Brake, Rear is inevitably working
Unexpectedly the Pad of Rear brake is decreasing quickly
In that situation I chose Replace as CARBONE LORRAINE
Because it is Rear, I made this RX 3 by saying that Standard specifications are enough

There is no complaint at all
It's such a Pad that I'm glad I made it

Helpful?

Fits:KAWASAKI ZR400 ZRX II 95 Use for:Rear Number Required:1, KAWASAKI ZR400 ZRX II 96 Use for:Rear Number Required:1, KAWASAKI ZR400 ZRX II 97 Use for:Rear Number Required:1, KAWASAKI ZR400 ZRX R 98- Used for:Rear:1, KAWASAKI ZR400 ZRX II 98- Used for:Rear:1

flexible (e.g. in terms of impact)

Very Good

Jun 8, 2019

When I did the overhaul of the rear brake area, I also changed the pad I changed the OEM pad as it was not changed for 22,000km since I bought a new car, but the OEM pad was not used at all I didn't Basically, I don't know much of a difference between fee rings because I don't use rear brakes much The state before the replacement of MASTEROH & CaliperOH & Fluid It's impossible to make a character imprint because it's different from But, well, as far as Feel is concerned, it's an extension of the OEM It's not overly effective or completely ineffective, it's just a matter of putting Front and Rear together in the same brand This was an OK choice because I just wanted to have it all in Pad, probably, but in terms of efficacy I think it's pretty easy to use for speed fine tuning while cornering

Helpful?

Fits:DUCATI 992 Multistrada 02- Application Area:Rear Number Required:1, DUCATI 944 ST2 98-02 Use part:Rear Necessary quantity:1, DUCATI 916 ST4S ABS 99- Use at:Rear Number Required:1, DUCATI 900 Supersport 98- Used for:Rear:1, DUCATI 916 ST4 ABS 99- Use at:Rear Number Required:1

Not available for OEM Caliper

Excellent

Apr 28, 2019

RSV4 OEM Caliper has a heat shield in the piston, so the thickness of the RX3 is not as thick as that of the RX3 I'm not going in
After Brembo crab is no problem
I replaced the Caliper for installation
The in-play stars were my impressions of the VTR1000F when it was on
You must check the inner diameter of the Piston for heat shielding before you install it

Helpful?

Fits:APRILIA Pegaso 650 01- i.e TTR Location:Rear Number Required:1, APRILIA Pegaso 650 01- i.e Part Number:Rear Number Required:1, APRILIA Pegaso 650 01- i.e Trail Location:Rear Number Required:1, APRILIA Dorsoduro 1200 ABS 11- Location:Rear Number Required:1, APRILIA Caponord 1200 Rally 13- Location:Rear Number Required:1

Excellent

Dec 16, 2018

Not bad

2017 BMW S1000RR. installation is perfectly fine. not gone to Circuit However, the braking power on the Pass Level is comparable to that of the OEMs, especially in terms of Dust I didn't find any defects, and the look of the Caliper gap isn't too bad (a little (Orange is back) I couldn't give it a Life rating because I just put it on, so I gave it 3 stars for now